Toyota Camry

1996-2001 of release

Repair and car operation



Kamri's Toyota
+ 1. Maintenance instruction
+ 1.2. Information before car driving
+ 1.3. Independent maintenance
+ 1.4. Technical characteristics
+ 1.5. Some councils upon car purchase
+ 2. Maintenance
- 3. Engines
   + 3.1.2. Compression check
   + 3.2. 6-cylinder dvukhryadny engines of V6 3,0 l
   + 3.3. Partition of engines
   + 3.4. Engine electric equipment
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. Exhaust system
+ 8. Transmission
+ 9. Running gear
+ 10. Brake system
+ 11. Body
+ 12. Electric equipment
generika kamagra bestellen auf rezeptfreide24.com potenzmittel generika -



3. Engines

3.1. 4-cylinder engines of 2,2 l

3.1.1. Technical characteristics

GENERAL INFORMATION

Type of an impellent compartment of models with the 4-cylinder engine

1. Tank of liquid of system of hydrostrengthening of a steering
2. Cover of a maslonalivny mouth
engine
3. Wires of spark plugs
4. Ignition coil
5. Tank of brake liquid
6. Casing of the air filter
7. Accumulator
8. Shchup for measurement of level of liquid of an automatic transmission
9. Shchup for measurement of level of oil of the engine
10. Oil filter
11. Cover of a bulk mouth of a radiator
12. Radiator hose
13. Tank of liquid of stekloomyvatel
14. Broad tank
15. Block of the relay and fuses

Marking
5S-FE
Volume
2,2 liters
Numbering of cylinders (from a gas-distributing belt to a transmission)
1–2–3–4
Sequence of operation of cylinders
1–3–4–2
Head of cylinders
The most admissible deformation:
  – the surface of a head which is joining to the block of cylinders
0,508
  – inlet and final collectors
0,300
Gas-distributing belt
Length of a spring of an intermediate pulley in a free condition
46,000
Camshaft
Diameters of necks of bearings
26,960-26,975
  – lubricant gap of the bearing:
     • the standard
0,026-0,061
     • the limiting
0,100
     • admissible wear
0,041
Cam height
  – camshaft of inlet valves:
     • the standard
42,010-42,110
     • the limiting
41,900
  – camshaft of final valves:
     • the standard
40,061-40,160
     • the limiting
39,949
Axial gap
  – camshaft of inlet valves:
     • the standard
0,046-0,099
     • the limiting
0,119
  – camshaft of final valves:
     • the standard
0,031-0,084
     • the limiting
0,099
Trailer gap of a spring of a gear wheel of a camshaft
22,505-22,911
District gap of camshafts
The standard
0,020-0,201
The limiting
0,478
Lift of valves
Diameter of the lift
30,965-30,975
Diameter of a nest
31,001-31,018
Lubricant gap
The standard
0,023-0,051
The limiting
0,071
Oil pump
  – a gap between a conducted gear wheel and a pump casing:
     • the standard
0,094-0,160
     • the limiting
0,201
  – a gap between a teeth of gear wheels:
     • the standard
0,041-0,160
     • the limiting
0,201

Moments of an inhaling of carving connections

Bolts and nuts of an inlet collector
19
Bolts of a clamp of an inlet collector
39
Bolts and nuts of a final collector
49
Bolts of the balancing device of the engine
49
Bolt of a pulley of a cranked shaft
109
Bolts of a flywheel or leading disk
Flywheel bolts (mechanical transmission)
88
Bolts of a leading disk (automatic transmission)
83
Bolts of an intermediate pulley
42
Bolts of a head of cylinders
Step 1
49
Step 2
Tighten on 90 degrees (a turn quarter)
Bolts of a cover of the radical bearing
19
Bolt of an asterisk of a cranked shaft
54
Bolts of the oil pump
9
Nut of an asterisk of the oil pump
25
Bolts and nuts of a maslozaborny branch pipe
6
Bolts of the oil pallet
6
Nuts of tubes of spark plugs
45
Bolts of a clamp of a back epiploon of a cranked shaft
12
Engine fastenings
Top bolt of a forward support
64
The bolts, fixing an arm of a forward support to the engine
64
The bolts, fixing a forward support to a body
Silver color
44
Green color
65
Top bolt of a back support
64
The bolts, fixing an arm of a back support to the engine
64
The nuts, fixing a back support to a body
65
Bolts of the right draft regulating shift of the engine
64
The bolts, fixing an arm of the right support to the engine
52