Toyota Camry

1996-2001 of release

Repair and car operation

Stop the engine and include emergency blinking signals.

Reliably involve the parking brake and establish a transmission in the situation "P" (an automatic transmission) or on a reverse gear (a transmission with manual switching).

All should leave the car in the opposite party from movement.

Attentively read the following instructions:

In a jack usage time surely be careful for reduction of risk of receiving a trauma. Follow instructions for work with a jack.

Do not start and do not scroll the engine when the car is supported only by a jack.

Stop the car on a firm equal surface, reliably involve the parking brake and establish a transmission in the situation "P" (an automatic transmission) or on a reverse gear (a transmission with manual switching). If it is required, enclose a block under a wheel located on a diagonals, opposite from a replaced wheel.

Surely establish a jack properly on a point for a jack. The car raising incorrectly located jack will damage the car or presumes to come off to the car a jack and to become the trauma reason.

Never подлезайте under the car when it is supported by only one jack.

Use a jack only for concept of the car during wheel replacement.

Do not lift the car when somebody is in car salon.

At a raising of the car do not enclose any subjects on or under a jack.

Lift the car only on height, sufficient for removal and tire replacement.

1. A wrench for nuts of wheels 2. A bag with tools 3. Jack 4. Jack handle 5. Spare tire

Take demanded tools and the spare tire.

For independent preparation for a critical situation it is necessary to familiarize with use of the jack, each tool and a place of their storage

Turn jack connection by a hand.

For removal – turn connection in the direction 1 until the jack will not be free.

For storage – turn connection in the direction 2 until the jack will not be reliably fixed for prevention of its moving forward during collision or sharp braking.

Removal of the spare tire

At storage of the spare tire establish it into place outer side of a wheel outside. Then fix the tire, repeating the above described points for removal upside-down for prevention of its advance during collision or sharp braking.

When blocking wheels put a block in front for forward wheels or behind for back wheels.

Aluminum wheels

Remove a decorative cover of a wheel by means of the pointed end of a wrench for nuts of wheels.

Do not try to remove a decorative cover a hand.

Always weaken nuts of wheels before a car raising.

Nuts turn counter-clockwise for their easing. For receiving the maximum lever effort establish a wrench on a nut so that the handle was on the right side, as shown. Grasp the handle near the end pull for the handle up. Be careful, that the wrench did not come off a nut.

Do not remove for the present a nut – only unscrew them approximately on one and a half turn.

Car raising

Lift the car on height, sufficient for installation of the spare tire. Remember that the bigger gleam with the earth is required at installation of the spare tire, than at removal of the lowered tire.

For a raising of the car insert the jack handle into a jack (free landing) and turn it clockwise. As soon as the jack will touch the car and will start to lift it, check twice that it is located correctly.

Replacement of wheels


Remove nuts of a wheel and replace tires.

Remove the lowered tire directly forward and put it aside.

Drive a spare wheel in the necessary situation and combine openings in c wheel bolts. Then lift a wheel and achieve, that the top bolt passed in an opening. Shake a wheel and put on it other bolts.

Tighten each nut gradually for one time in the sequence specified in drawing. Repeat process until all nuts will not be completely tightened.

Return installation of a decorative cover of a wheel

Establish back decorative cover of a wheel:

Steel wheels

Establish a decorative cover of a wheel in the correct situation.

Aluminum wheels

On some models – combine a cut on a decorative cover of a wheel with a gate core.

Then reliably knock her edge of a hand for its zashchelkivaniye on a place.

Adjust pressure of air to the demanded. If it is lower, slowly reach to the next service station and pump up the tire to the necessary pressure.

Do not forget to establish back a cap of the inflatable gate of the tire as dirt and moisture can get to a gate core that will lead to leakage of air. If the cap was lost, establish new as soon as possible.

Before driving be convinced that all tools, a jack and the lowered tire are reliably fixed in places of their storage to avoid a trauma during collision or sharp braking.