Toyota Camry

1996-2001 of release

Repair and car operation

For control for previously established station – to press the button of desirable station. Button or cell number and frequency of station will appear on the display.

These systems can remember one station DV/SV and three VHFs of station under each button. (The display will show "LW" or "MW", "U1", "U2" or "U3" when will press the BAND button). Memory the established stations will be cancelled previously, if giving of a food is interrupted (the storage battery will be disconnected or will fuse the fuse).

        Pushing out button

Press this button for cartridge pushing out.

| / |            higher / low number of a path

Using this button, it is possible to pass to higher / low number of a path or quickly to scroll forward / back a path to which listen.

Transition to higher / low number of a path – quickly to press and release the button  >> | (up) or | << (down). Number of a path will appear on the display. If will hear a zummerny signal then you held the button too long, and the player quickly will scroll a path forward or back.

Fast scrolling of paths forward / back – to press and hold the button >> | (forward) or | << (back) until will hear a zummerny signal. While you hold the button, the current time of reproduction is displayed on the display. Until then while you will hold the button, the player quickly will scroll a path forward/back. When release the button, the player will renew reproduction.

AF (alternative frequencies)

This button is used for search of RDS stations (radio information system) in all strip of frequencies.

To press "AF" less than for 2 seconds for reception of the same program during control for RDS station. "AF" will appear on the display. If conditions of reception worsen, the network which transfers the same program, will be chosen according to the AF list (alternative frequencies) for RDS stations.

For AF mode change – to press the AF button at least for 2 seconds. When "REG ON" will appear on the display, the radio receiver will choose RDS station which has the same PI code (program identification). When "REG OFF" appears on the display, the radio receiver chooses the RDS station having the same three-value digital PI code (program identification).

If the radio receiver cannot find RDS station within 60 seconds, the radio receiver muffles all programs and starts to look for RDS station of the same PI code with AF list use. If the radio receiver cannot find any station for one pass owing to weak signals, he starts to look for again with use of more strengthened sensitivity for search of stations with a weak signal. At this time on the display there will be an indication of "DX". The zummerny signal will sound, and on the display there will be "PI SEEK" indication, reporting about when this function starts to work.

If the signal becomes the weakest, the radio receiver will suspend station search, and on the display within 2 seconds there will be "NOTHING" indication. After that, if the radio receiver cannot find RDS station within 20 seconds, it starts search over again.

For AF mode cancellation once again press the AF button.

AST (Automatic storing)

This button is used for automatic preliminary installation of frequencies of 6 radio stations for each strip of frequencies (DV/SV, UKV1, UKV2 and UKV3).

Press "AST" until will hear a zummerny signal. If the radio receiver cannot find any station, it will be adjusted on frequency which accepted before AST function use.

BAND

To press "BAND" for switching between strips of frequencies DV/SV and VHF.

"LM", "MW", "U1", "U2" or "U3" will appear on the display. These systems allow to establish eighteen VHFs stations from calculation on three on each button.

If the audiosystem is switched off, it is possible to include a radio receiver in "BAND" pressing. Also it is necessary to press "BAND" for switching from work with the cartridge or a compact disc work with a radio receiver.

CD (Compact disc)

Press "CD" for switching from work with a radio receiver or the cartridge work with a compact disc, it is possible to turn on the CD player by "CD" pressing.

When the audiosystem is established for work with a compact disc, the display will show number of a path of the current reproduction.

DISC

By pressing of this button it is possible to choose a disk to which wish to hear.

Hollow NR

If the tape which has been written down with use of system of a shumopodavleniye is used Hollow, press the button designated by a symbol of a double letter D. The symbol of a double letter D will be displayed on the display. Press the button again for switching off of system Hollow NR.

Mode Hollow NR reduces tape noise approximately to 10 dB. For the best reproduction of a sound reproduce tapes with switched-on or switched-off this button depending on a mode used for record of a tape.

System of a shumopodavleniye Hollow it is made according to the license Dolbi Laboratoriz Laysensing Korporeyshen. "DOLBY" and a symbol of a double letter D are trademarks Dolbi Laboratoriz Laysensing Korporeyshen.

FF (The accelerated rewind forward)

Press the FF button for performance of the accelerated rewind of a tape forward. For a tape stop during the accelerated rewind forward slightly press the REW button.

When the tape will be rewound forward up to the end, the cassette player will begin reproduction of other party of a tape by means of function of an automatic reverse.

Indication MTL (Metal)

Press the MTL button at an insert of a metal or chromic tape. On the display there will be "MTL" indication.

PROG (Program)

Press both PROG buttons for a choice of other party of a cassette tape. Automatic reversion function. After the cassette player reaches the end of one party of a tape, it automatically changes the direction and starts to reproduce other party. It occurs, is not dependent on, whether the cartridge is reproduced or is accelerated is rewound forward.

RTY (program type)

Press the PTY button. If the button is pressed during code reception "by PTY RDS station, type of the current NEWS program (news), "SPORT" (sports), "TALK" (conversation), "POP" (pop music), "Classics" (classics) appears on the display. If other type of the program is required, to press PTY until there will be a desirable type of the program.

If the button "^" or "TUNE v" is pressed by TUNE during display such as the program on the display, the radio receiver will look for station which transfers the PTY code. If the radio receiver cannot find any station, on the display there will be "NOTHING" indication.

If the system remains untouched within 6 seconds during display such as the program or if other operation is carried out, indication such as the program disappears and the radio receiver will transfer the program of the last displayed type of the program.

PWR (Food)

To press "PWR" for inclusion and audiosystem switching off.

RAND any)

There are two functions of any reproduction. You can hear to all paths in any sequence on all compact discs in shop or hear in any sequence only to paths on a certain compact disc.

Any reproduction of paths on a disk – quickly to press and release the RAND button. "RAND" will appear on the display, and the player will reproduce all paths of that disk to which you listen, in any sequence. If will hear a zummerny signal then held the button too long, and the player will reproduce in any sequence all paths from all disks which are available in shop. For switching off of function of any reproduction press the RAND button again.

Any reproduction of all paths in shop – press "RAND" until will hear a zummerny signal. "D*RAND" will appear on the display, and the player will reproduce all paths from all disks in shop in any sequence. For switching off of function of any reproduction press the RAND button again.

REW (The accelerated rewind back)

Press the REW button for performance of the accelerated rewind of a tape back. For a tape stop during the accelerated rewind forward slightly press the FF button. Tape reproduction immediately will begin.

When the tape will be rewound back up to the end, the cassette player will stop, and then reproduction of the same party will begin.

RDS display (radio information system)

The radio receiver is automatically switched to the RDS mode for RDS station reception during broadcasting VHF control. "RDS" and the name of RDS station appear on the display.

RPT (Repetition): CD player

There are two functions of repeated reproduction. It is possible to reproduce repeatedly a path of a disk or the whole compact disc. Path repetition – quickly press and release the RPT button until will hear a zummerny signal. "D*RPT" will appear on the display. The player will repeatedly reproduce all paths of that disk to which listen.

When reproduction of a disk will end, the player will automatically pass to an initial path of a disk and will execute repeated reproduction. This process will proceed until will press the button again for switching off of this function.

SCAN

RADIO RECEIVER

You can scan all frequencies of a strip or only frequency previously the established stations of this strip of frequencies.

For scanning of frequencies previously the established stations – quickly press and release the SCAN button. If will hear a zummerny signal, means, held the button too long, and the radio receiver will scan all frequencies of a strip. The radio receiver will be adjusted on the established station following previously up on a strip of frequencies and will reproduce it within several seconds, and then will pass to the established station following previously. For a station choice once again press the SCAN button.

CD PLAYER

There are two functions of scanning. It is possible to scan paths of a certain disk or the first paths of all disks in shop.

Scanning of paths of a disk – quickly press and release the SCAN button. "SCAN" will appear on the display, and the player will scan all paths of a listened disk. If will hear a zummerny signal, means, held the button too long, and the player will scan the first paths of disks of shop. For a path choice once again press the SCAN button. If the player scans all paths of a disk, it will stop scanning.

Scanning of the first paths of disks of shop – press the SCAN button until will hear a zummerny signal. "D*SCAN" will appear on the display, and the player will reproduce the first path of the following disk within 10 seconds, and then will pass to scanning of the following disk. For a choice of a disk to press the SCAN button the second time. If the player scans all disks, it will stop scanning.

SEL (Choice) and VOL (Loudness)

VOLUME CONTROL FUNCTION

These buttons are used for volume control. For volume control repeatedly to press "SEL" until "VOL" will not appear on the display. Then to press the party "^" (up) or "v" (down) the VOL buttons. The display will show a range from "VOL 0" to "VOL 36".

FUNCTION OF ADJUSTMENT OF SOUND BALANCE

These buttons are used for adjustment of sound balance between the right and left and forward and back speaker systems.

For adjustment of the right / left balance repeatedly to press "SEL" until "BAL" will not appear on the display. Then to press the party "^" (up) or "v" (down) the VOL buttons.

The display will show a range from "BAL L7" to "BAL R7".

For adjustment of forward/back balance repeatedly to press "SEL" until "FAD" will not appear on the display. Then to press the party "^" (up) or "v" (down) the VOL buttons.

The display will show a range from "FAD F7" to "FAD R7".

FUNCTION OF MANUAL ADJUSTMENT OF THE TIMBRE

These buttons also are used for timbre adjustment manually.

For adjustment of a timbre of low tone repeatedly press the SEL button until "BAS" will not appear on the display. Then press the party "^" (up) or "v" (down) the VOL buttons for adjustment to own taste.

The display will show a range from "BAS-5" to BAS +5".

For adjustment of a timbre of a high-pitch tone repeatedly press the SEL button until "TRE" will not appear on the display. Then press the party "^" (up) or "v" (down) the VOL buttons for adjustment to own taste.

The display will show a range from "TRE-5" to "TRE +5".

ST indication (Stereophonic reception)

The radio receiver automatically passes to stereophonic reception at control for a stereophonic broadcast. "ST" appears on the display. If the signal becomes weak, the radio receiver lowers value of a razneseniye of channels for prevention of creation of noise because of a weak signal. If the signal becomes extremely weak, the radio receiver is switched from stereophonic reception to the monophonic.

THAT (Road news)

This button is used for reception of THAT stations on all strip of frequencies.

EON system (additional expanded network). If the RDS station (with EON data) to which you listen, does not transfer the program of road information in THAT mode (road news), the radio receiver is switched to the program of road information automatically with AF list use for EON.

After the completion of transfer of road information the radio receiver automatically comes back to the initial program. The Zummerny signal reports, when this function begins and stops to work.

To press "THAT" for radio receiver switching a TR mode. "TR" will be displayed on the display.

In a TR mode the radio receiver begins TR station search. When the TR station will be accepted, the name of program service will appear on the display. Also in the AF mode the radio receiver looks for TR station with AF list use.

If the radio receiver cannot find any TR station, "NOTHING" appears on the display for 2 seconds and search of TR station is started over again.

When the TR station will be accepted, if the signal of TR stops for 20 seconds, the radio receiver starts to look for other TR station automatically.

Again press "THAT" for radio receiver switching THAT mode. "THAT TR" will appear on the display.

In THAT mode the radio receiver starts to look for TR station. It will sound only when the TR station will be accepted. When the TR station will be accepted, the name of program service will appear on the display. Also in the AF mode the radio receiver looks for TR station with AF list use.

If the radio receiver cannot find any TR station, "NOTHING" appears on the display for 2 seconds and search of TR station is started over again.

When the TR station will be accepted, if the signal of TR stops for 20 seconds, the radio receiver starts to look for other TR station automatically.

Function of storing of loudness "THAT" is remembers loudness at reception of road news.

When "TA" is accepted next time, the system compares loudness of the accepted TA station and the remembered loudness THAT and automatically chooses higher loudness. But the range of storing of loudness is limited: if loudness of earlier accepted program above the maximum loudness of a range, is remembered the maximum loudness of a range and if it is lower than the minimum loudness of a range, the minimum loudness of a range is remembered.

You can adjust loudness irrespective of the remembered loudness "THAT" at TA station reception (see SEL and VOL).

For return to a normal mode from THAT mode once again press "THAT".

TAPE

To press "TAPE" for switching from radio receiver work work of a cassette player. If the audiosystem is switched off, it is possible to include a cassette player in "TAPE" pressing. In both cases the cartridge should be already inserted into a player.

TUNE

Control

The Toyota car has a radio receiver with electronic control (ETR). To press and release the party "^" (up) or "v" (down) the TUNE buttons for change of frequency of station up or down on a strip of frequencies. If will hear a zummerny signal, it means that held the button too long and the radio receiver will enter into a search mode.

Search

The radio receiver finds in a search mode and reproduces the following station up or down on a strip of frequencies. For station search – to press and take the side "^" or TUNE button "v" until will hear a zummerny signal. For finding of other station execute this procedure again.