Toyota Camry

1996-2001 of release

Repair and car operation



Kamri's Toyota
+ 1. Maintenance instruction
+ 1.2. Information before car driving
+ 1.3. Independent maintenance
+ 1.4. Technical characteristics
+ 1.5. Some councils upon car purchase
- 2. Maintenance
   2.2. Schedule of servicing of Toyota Camry/Avalon
   2.3. Primary and secondary checks
   2.4. Check of level of oil and liquids
   2.5. Check of a condition of tires and pressure in tires
   2.6. Check of level of liquid of system of hydrostrengthening of a steering
   2.7. Check of level of AKPP liquid
   2.8. Replacement of engine oil and oil filter
   2.9. Survey and replacement of brushes of screen wipers
   2.10. Check, servicing and battery charging
   2.11. Check, adjustment of a tension and replacement of a driving belt
   2.12. Check and replacement of hoses in an impellent compartment
   2.13. Check of system of cooling
   + 2.14. Shift of wheels
   2.15. Check of brake system
   2.16. Replacement of the air filter
   2.17. Power supply system check
   2.18. Check of level of liquid of differential (AKPP)
   2.19. Check of level of MKPP oil
   2.20. Steering and suspension bracket check
   2.21. Check of covers of semi-axes
   2.22. Check of final system
   2.23. Height and free wheeling of pedals of coupling and brake
   2.24. Replacement of the fuel filter
   2.25. Replacement of cooling liquid and washing of system of cooling
   2.26. Check of the system, supervising allocation паров fuels
   2.27. AKPP liquid replacement
   2.28. MKPP oil replacement
   2.29. Check of fastenings of a body
   2.30. Check and replacement of spark plugs
   2.31. Check and replacement of wires of spark plugs
   2.32. Check and adjustment of gaps of valves
   2.33. Replacement of laying of a cover of a jellied mouth of a fuel tank
   2.34. Check and replacement of the valve of ventilation of a case
+ 3. Engines
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. Exhaust system
+ 8. Transmission
+ 9. Running gear
+ 10. Brake system
+ 11. Body
+ 12. Electric equipment
BQ BQS-5520



2.4. Check of level of oil and liquids

GENERAL INFORMATION

Engine oil

Arrangement щупа for check of level of oil
Shchup for check of level of oil (it is specified by an arrow) is located on the right back side of the engine. Level of oil is necessary for checking before a trip on the car or in 15 minutes after engine switching off.

Shchup for check of level of oil

 

Get щуп and wipe the end щупа. Insert щуп up to the end into a tube and again get it. Level of oil should be between two lines on щупе. The difference in number of oil between marks on щупе makes about 1 liter.

Bulk mouth

To add oil braid the cap of a bulk mouth located on a cover of a head of cylinders, insert into a mouth a funnel (it is specified by an arrow) and fill in oil.

Cooling liquid

Regularly check level of cooling liquid in a tank with the help щупа or marks in a tank wall. When the engine is heated-up, level of liquid should raise to the top mark. Add cooling liquid if it is necessary.

Tank for cooling liquid
Check, that level of cooling liquid was between Full and Low marks. If necessary add the necessary amount of antifreeze and water.

At check of level of cooling liquid also check a condition of the liquid. If liquid gained brown or rusty color, it it is necessary to replace and wash out cooling system.

Washing liquid

Tank for liquid of washers

The tank for liquid of washers of a windshield is located in the right forward corner of an impellent compartment. Check, that level of liquid was near the top mark in a jellied mouth.

In warm climate fill in a tank only on two thirds, and in a frigid climate, use solution of special nonfreezing liquid. Do not use antifreeze as it can damage car paint.

Liquid of a hydraulic drive of brakes and coupling

Check, that level of liquid was between marks the MOVE and MIN located on a wall of a tank. Add liquid of demanded type if it is necessary.

Check a condition of the liquid if at it there are parts of dirt or a water droplet, liquid it is necessary to merge and fill system with new liquid.