Toyota Camry

1996-2001 of release

Repair and car operation



Kamri's Toyota
+ 1. Maintenance instruction
+ 1.2. Information before car driving
+ 1.3. Independent maintenance
+ 1.4. Technical characteristics
+ 1.5. Some councils upon car purchase
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. Exhaust system
+ 8. Transmission
+ 9. Running gear
- 10. Brake system
   10.2. Technical characteristics
   10.3. ABS system
   10.4. Blocks of disk brakes
   10.5. Brake support
   10.6. Brake disk
   10.7. Blocks of drum-type brakes
   10.8. Wheel cylinder of brakes
   10.9. Main cylinder of brakes
   10.10. Hoses and hydraulic actuator tubes
   10.11. Air removal from a hydraulic actuator of brakes
   10.12. Vacuum amplifier of brakes
   10.13. Blocks of the parking brake of back disk brakes
   10.14. Parking brake
   10.15. Cables of the parking brake
   10.16. Switch of a signal of braking
   10.17. ABS: natural choice
   10.18. Malfunctions of brake system
+ 11. Body
+ 12. Electric equipment


10.4. Blocks of disk brakes

GENERAL INFORMATION

Replacement
Prevention

Blocks change only in a set on one axis. When cleaning blocks a dust and dirt to delete with wiping by rags moistened in alcohol or special liquid, it is forbidden to blow. Considered procedure is applicable to blocks of back and forward brakes.


PERFORMANCE ORDER
1. Unscrew a stopper of a nutritious tank of brakes.
2. Release nuts of wheels, lift the car (a lobby or a back part) and establish on supports.
3. Remove wheels.
4. Attentively check a disk condition (see subsection 10.6.). In need of grinding or replacement remove a disk and blocks.
5. Drown pistons in cylinders to establish new blocks. If necessary use a clamp. In process of a piston utaplivaniye liquid level in a tank will raise. Remove excess of liquid, having sucked away a syringe.
6. Before work clear brake details special structure.
7. Unscrew the bolts specified by the top and bottom arrows (a bolt of the union of a hose to turn on only if the support acts in film from the car).
8. Remove a support.
9. Fix a support a wire, without allowing sagging on a hose.
10. Remove the top antinoise spring of blocks (on 4-cylinder models).
11. Remove the bottom antinoise spring of blocks (on 4-cylinder models).
12. Remove external and internal antinoise plates from an external block.
13. Remove an external block.
14. Remove external and internal antinoise plates from an internal block.
15. Remove an internal block.
16. Remove clamps of blocks, check their condition and if necessary replace (clamps should be latched in nests support arms, at detection of deformations or weakening of landing clamps replace).
17. Hook and remove the wear index from an internal block and rearrange the index on a new block. At detection of damages the indicator replace.
18. Establish the block clamp, a new internal block and antinoise plates. Track that ears of antinoise plates came into grooves on clamps of blocks.
19. Establish the block clamp, a new external block and antinoise plates.
20. Establish the top and bottom antinoise springs of blocks (on 4-cylinder models), track, that springs entered into gearing with blocks.
21. Get the top and bottom fingers of a block and clear them (replace the damaged rubber cover, having hooked a fillet on the metal plug).
22. Then grease a finger with refractory greasing and establish into place.
23. Establish a support and tighten bolts with the set moment.
24. Before replacement of back disk brakes clear brake details.
25. Unscrew a bolt of fastening of a support (it is specified by the bottom arrow), the bolt of the union of a hose (the top arrow) to turn on only if the support acts in film from the car.
26. Cast away a support and fix.
27. Remove an external and internal antinoise plate from an external block.
28. Remove an external block.
29. Remove an external and internal antinoise plate from an internal block.
30. Remove an internal block.
31. Remove clamps of blocks, check their condition and if necessary replace (clamps should be latched in nests of an arm of a support, at detection of deformations or weakening of landing clamps replace).
32. Establish the block clamp, a new internal block and antinoise plates. Track that antinoise plates entered into gearing with blocks and with each other.
33. Establish the block clamps, a new external block and antinoise plates. Track that antinoise plates entered into gearing with an external block with each other.
34. Lower a support, having put on it new blocks. Tighten a bolt with the set moment.

35. Upon termination of assembly several times press a brake pedal to reduce blocks with a disk. Check liquid level, if necessary add. Check work of brakes.