Toyota Camry

1996-2001 of release

Repair and car operation


Kamri's Toyota
+ 1. Maintenance instruction
+ 1.2. Information before car driving
+ 1.3. Independent maintenance
+ 1.4. Technical characteristics
+ 1.5. Some councils upon car purchase
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. Exhaust system
+ 8. Transmission
+ 9. Running gear
- 10. Brake system
   10.2. Technical characteristics
   10.3. ABS system
   10.4. Blocks of disk brakes
   10.5. Brake support
   10.6. Brake disk
   10.7. Blocks of drum-type brakes
   10.8. Wheel cylinder of brakes
   10.9. Main cylinder of brakes
   10.10. Hoses and hydraulic actuator tubes
   10.11. Air removal from a hydraulic actuator of brakes
   10.12. Vacuum amplifier of brakes
   10.13. Blocks of the parking brake of back disk brakes
   10.14. Parking brake
   10.15. Cables of the parking brake
   10.16. Switch of a signal of braking
   10.17. ABS: natural choice
   10.18. Malfunctions of brake system
+ 11. Body
+ 12. Electric equipment


10.15. Cables of the parking brake
GENERAL INFORMATION

Details of a hummock drive of the parking brake
1. Hatch cover
2. An arm (cars with separate seats)
3. N4 parking brake cable
 4. Intermediate lever
5. N1 parking brake cable
6. Plug
7. Intensifying section

Details of a hummock drive from a pedal to the intermediate lever
1. Cable of an otpuskaniye of the parking brake
2. Overlay of a pedal
3. N1 parking brake cable
4. Bracket
5. Axis
6. Switch of a signal of the parking brake

Replacement

THE CABLE CONNECTING THE LEVELING LEVEL TO PARKING BRAKES OF BACK WHEELS

PERFORMANCE ORDER
1. Lift a back part of the car.
2. Release the parking brake and remove a drum (disk).
3. On and/m with back drum-type brakes remove blocks and disconnect a cable from the lever of a drive of a block. On and/m, equipped with back disk brakes, remove blocks of the parking brake and disconnect the lever of a drive of a block.
4. Unscrew bolts of a tip of a cable of the parking brake on a brake board.
5. Unscrew a bolt of fastening of an arm of a cover of a cable. The arm of a cover of a cable is located in a forward part of a bar of a back suspension bracket (on a part of cars the arrangement of an arm can differ a little).
6. Remove average section of an exhaust pipe (or приопустите it) to provide access to cables.
7. Unscrew a bolt of fastening of a collar of a forward tip of a cover of a cable and deduce a tip from a collar.
8. Turn a cable so that the tip of a cable left gearing with a level of the equalizer and unhook a cable.
9. Installation is carried out upside-down.
10. Adjust a cable.

THE CABLE CONNECTING THE INTERMEDIATE LEVER TO THE LEVELING LEVEL

PERFORMANCE ORDER
1. Remove the central section.
2. Release the lever of a brake and unscrew a lock-nut and adjusting nuts. Disconnect a cable from the lever.
3. Working under the car, submit a cable back, turn on 90 ° and extend a cable, having passed through an opening in a floor.
4. Installation is carried out upside-down. Grease rubbing parts of a tip of a cable in a leveling level. Adjust a cable.

THE CABLE CONNECTING THE INTERMEDIATE LEVER TO THE PEDAL (ONLY FOR THE AVALON MODELS)

PERFORMANCE ORDER
1. Remove a forward seat.
2. On and/m with a seat of skameechny type remove intensifying section, on and/m with separate seats remove the central section.
3. Disconnect a cable from the intermediate lever.
4. Remove the knee buffer of safety (see subsection 11.23.).
5. Disconnect the switch of a signal of the parking brake.
6. Rasshplintuyte also get a pedal axis, disconnect from a pedal a cable.
7. Installation is carried out upside-down.