Toyota Camry

1996-2001 of release

Repair and car operation


Kamri's Toyota
+ 1. Maintenance instruction
+ 1.2. Information before car driving
+ 1.3. Independent maintenance
+ 1.4. Technical characteristics
+ 1.5. Some councils upon car purchase
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. Exhaust system
+ 8. Transmission
+ 9. Running gear
- 10. Brake system
   10.2. Technical characteristics
   10.3. ABS system
   10.4. Blocks of disk brakes
   10.5. Brake support
   10.6. Brake disk
   10.7. Blocks of drum-type brakes
   10.8. Wheel cylinder of brakes
   10.9. Main cylinder of brakes
   10.10. Hoses and hydraulic actuator tubes
   10.11. Air removal from a hydraulic actuator of brakes
   10.12. Vacuum amplifier of brakes
   10.13. Blocks of the parking brake of back disk brakes
   10.14. Parking brake
   10.15. Cables of the parking brake
   10.16. Switch of a signal of braking
   10.17. ABS: natural choice
   10.18. Malfunctions of brake system
+ 11. Body
+ 12. Electric equipment


10.5. Brake support
GENERAL INFORMATION

Details of a forward brake (for models with the 4-cylinder engine)
1. Support
2. Support arm
3. Sealant
4. Finger
5. Rubber cover
6. Clamps of blocks (for cars with the engine 5S-FE)
7. Clamps of blocks (for cars with the engine 1MZ-FE)
8. Antinoise plates
9. Internal antinoise plate
10, 13. Spring of an antinoise plate
 11. Internal block
12. External block
14. The index of wear of a block (for cars with the engine 1MZ-FE)
15. Cover
16. Epiploon
17. Finger
18. Sealing ring of the piston
19. Restrictive ring of the piston
20. Piston
21. The union for brake pumping

Details of a forward brake (for models with the 6-cylinder engine)

1. Support
2. Support arm
3. Disk
4. Sealant
5. Finger
6. Epiploon
7. Rubber cover
8. Clamps of blocks
9. Antinoise plates
10. Spring of an antinoise plate

11. External block
12. Internal block
13. Index of wear of a block
14. Cover
15. Finger
16. External sealant
17. Restrictive ring of the piston
18. Piston
19. Sealing ring of the piston
20. The union for pumping of brakes

Details of a back brake

1. Sealant
2. Support
3. The union for pumping of brakes
4. Cover of an axis of a support
5. External sealant of the piston
6. Piston
7. Sealing ring of the piston
8. Restrictive ring of the piston
9. Epiploon

10. Block clamp
11. Block
12. Internal antinoise plate
13. Antinoise plate
14. Rubber cover
15. Support assembled
16. Support arm
17. Cap
18. Disk

Removal
Prevention

Supports change in pair on one axis.

PERFORMANCE ORDER
1. Lift the car and remove wheels.
2. Close an opening of the union of a hose of a brake a piece of a rubber hose of suitable diameter. Unscrew a bolt of the union and disconnect a brake hose.
3. Unscrew bolts of fastening and remove a support.
4. If necessary remove an arm from a rotary fist or an arm of a back axis, having unscrewed the bolts specified by shooters. In drawing at the left – an arm of a forward support, on the right – back.

Installation

Installation is carried out upside-down. Tighten all bolts with the set moment. Remove air from a hydraulic actuator of brakes.