Toyota Camry

1996-2001 of release

Repair and car operation



Kamri's Toyota
+ 1. Maintenance instruction
+ 1.2. Information before car driving
+ 1.3. Independent maintenance
+ 1.4. Technical characteristics
+ 1.5. Some councils upon car purchase
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. Exhaust system
+ 8. Transmission
+ 9. Running gear
- 10. Brake system
   10.2. Technical characteristics
   10.3. ABS system
   10.4. Blocks of disk brakes
   10.5. Brake support
   10.6. Brake disk
   10.7. Blocks of drum-type brakes
   10.8. Wheel cylinder of brakes
   10.9. Main cylinder of brakes
   10.10. Hoses and hydraulic actuator tubes
   10.11. Air removal from a hydraulic actuator of brakes
   10.12. Vacuum amplifier of brakes
   10.13. Blocks of the parking brake of back disk brakes
   10.14. Parking brake
   10.15. Cables of the parking brake
   10.16. Switch of a signal of braking
   10.17. ABS: natural choice
   10.18. Malfunctions of brake system
+ 11. Body
+ 12. Electric equipment


10.13. Blocks of the parking brake of back disk brakes

GENERAL INFORMATION

Details of the parking brake

1. A directing level
2. Spring
3. Strut
4. Back block
5. Remote laying
6. Axis
7. Returnable springs of blocks
8. Support of a back disk brake
9. Cap
10. Disk
11. Clamping spring of a block
12. Cups of a clamping spring
13. Spring of blocks the pulling together
14. Regulator
15. Forward block
16. Axis
17. Lever of a drive of a block
18. Cutting washer

Prevention

Blocks of the parking brake change only in pair on an axis.


Check and replacement

PERFORMANCE ORDER
1. Remove a brake disk (see subsection 10.6.).
2. Check residual thickness of frictional slips. Blocks are subject to replacement, if thickness of a material less than 0,8 mm.
3. Remove a nave with bearings (see section 9.1.14.).
4. Clear brake details special structure.
5. Remove pulling together spring of a back block of the parking brake from an axis and unhook a spring from a back block.
6. Remove pulling together spring of a forward block of the parking brake from an axis and unhook a spring from a forward block.
7. Remove a clamping spring of a back block and get an axis.
8. Remove a strut.
9. Remove a clamping spring of a forward block and get an axis.
10. Remove a gap regulator between blocks and a disk drum (the pulling together spring is behind a regulator and in a picture it is not visible).
11. Get a cutting spring washer from an axis of the lever of a drive of a block of the parking brake on a back block and remove the lever.
12. Grease with a thin layer of refractory greasing a rubbing surface of a board of a brake.
13. Dress a cable on the lever and fix a spring cutting washer.
14. Dress pulling together spring from a reverse side of a back block and from a reverse side of a forward block.
15. Establish a regulator, having brought blocks to each other. The terminations of a regulator should enter into gearing with blocks.
16. Establish blocks, establish a strut and a spring. The bifurcate terminations of a strut should come into grooves of blocks.
17. Establish a returnable spring of a lobby and a back block.
18. Establish a clamping spring of a back and forward block
19. As a result of the correct assembly of a detail settle down as in drawing.
20. Establish a disk of a brake and fix, having screwed 3 nuts of a wheel.
21. Turn out from a disk a cap. Adjust blocks for what rotating a makhovichok of a hairpin of a regulator dissolve blocks against the stop in a drum (the drum thus should not rotate) and take away, having unscrewed a regulator makhovichok on 8 teeth.
22. Establish a support arm, tighten bolts with the set moment.
23. Establish a wheel.
24. On and/m, equipped with the lever of the parking brake, check number of clicks of the lever before complete braking which should be from 5 to 8. Otherwise adjust.
25. For extra earnings of blocks of the parking brake arrive as follows. On and/m, equipped with the lever of the parking brake, moving with speed of 50 km/h on the equal dry highway, include a brake, having made the lever effort 8кГс. On and/m with a pedal of the parking brake, include a brake, having put to effort to a pedal 13кГс. Having passed about 0,5 km, release a pedal.
26. Repeat this procedure 2–3 times, let's cool down previously to blocks.