Toyota Camry

1996-2001 of release

Repair and car operation

Kamri's Toyota
+ 1. Maintenance instruction
+ 1.2. Information before car driving
+ 1.3. Independent maintenance
+ 1.4. Technical characteristics
+ 1.5. Some councils upon car purchase
+ 2. Maintenance
- 3. Engines
   - 3.1.2. Compression check
      3.1.3. Top dead point (VMT) of the N1 piston
      3.1.4. Cover of a head of cylinders
      3.1.5. Inlet collector
      3.1.6. Final collector
      3.1.7. Gas-distributing belt and asterisks
      3.1.8. Forward epiploon of a cranked shaft
      3.1.9. Camshaft epiploon
      3.1.10. Camshafts and lifts of valves
      3.1.11. Head of cylinders
      3.1.12. Oil pallet
      3.1.13. Oil pump
      3.1.14. Flywheel / leader disk
      3.1.15. Back epiploon of a cranked shaft
      3.1.16. Engine fastenings
   + 3.2. 6-cylinder dvukhryadny engines of V6 3,0 l
   + 3.3. Partition of engines
   + 3.4. Engine electric equipment
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. Exhaust system
+ 8. Transmission
+ 9. Running gear
+ 10. Brake system
+ 11. Body
+ 12. Electric equipment

3.1.11. Head of cylinders

GENERAL INFORMATION

Head of cylinders of the engine 5S-FE

1. Valve of system of a retsirkulyatsiya
exhaust gases and vacuum converter
2. Laying
3. Laying
4. Throttle
5. A damper of pulsations in fuel system
6. Fuel hose
7. Laying
8. Inlet collector
9. Hose of return of fuel
10. Tube of supply of fuel
11. Sealing ring
11а Insulating plug
12. Injector
13. Insulator
14. Plug
15. Valve
16. Cover of a head of cylinders
17. Clamp
18. Adjusting laying
19. The isolating plug
20. Epiploon
21. Valve
22. Spark plug
23. Valve lift
24. Clamps
25. Plate of a spring
26. Valve spring
27. Spring saddle
28. Lock ring
29. The directing plug of the valve
30. Camshaft of final valves
31. A hook for an engine raising
32. Branch pipe of system of cooling

33. Pumping
34. Sensor of pressure of oil
35. Perepuskny tube of system of cooling
36. A heatisolating guard of an oil radiator
37. A heatisolating guard of a final collector
38. Kronshtya of a final collector
39. Kronshtya of a final collector
40. Final collector
41. Laying
42. Sealing ring
43. Laying
44. Head of cylinders
45. A hook for an engine raising
46. Grounding contact
47. Generator arm
48. Laying of a head of cylinders
49. Cover of a gas-distributing belt
50. Spring of a gear wheel of a camshaft
51. Lock ring
52. Washer
53. Epiploon
54. Additional gear wheel of a camshaft
55. Camshaft of inlet valves
56. Cover of the first bearing of a shaft
57. Laying
58. Fastenings of an inlet collector
59. Air tube
60. Laying
61. Vacuum tube
62. Vacuum valve of system of a retsirkulyatsiya

Removal

Sequence of a tightening of bolts of a head of cylinders

PERFORMANCE ORDER

1. Disconnect a wire of the minus plug of the accumulator.
2. Merge cooling liquid from a case of the engine and from a radiator.
3. Merge engine oil and remove the oil filter.
4. Remove a throttle, fuel injectors and the fuel highway.
5. Remove an inlet collector.
6. Remove a final collector.
7. Remove a gas-distributing belt, an asterisk of a camshaft and the top intermediate pulley.
8. Remove the top section of a back cover of a gas-distributing belt.
9. Remove camshafts and lifts of valves.
10. Remove the generator and the ignition distributor.
11. Unscrew bolts of the pump of the amplifier of a steering. Shift the pump aside, without disconnecting from it hoses.
12. Disconnect all wires, tubes, hoses and the ropes fixed on a head of cylinders.
13. Weaken and unscrew head bolts in sequence of return that which is specified in drawing Sequence of a tightening of bolts of a head of cylinders. Weaken bolts on a turn quarter at one time.
	14. Remove a head of cylinders.

Installation

PERFORMANCE ORDER

	1. Carefully clean and wipe acetone being joined surfaces of a head and the block of cylinders. If surfaces are scratched or damaged otherwise, they are necessary for processing in a specialized workshop.
2. By means of a suitable tap clean carvings in the block of cylinders. By means of a suitable die clean bolts of a head of cylinders.
3. Establish new laying of a head and establish a head.
4. Grease bolts with pure engine oil.
5. Insert bolts and tighten them till the demanded moment of an inhaling in sequence specified in drawing Sequence of a tightening of bolts of a head of cylinders.
6. Establish the remained details.