Toyota Camry

1996-2001 of release

Repair and car operation

Kamri's Toyota
+ 1. Maintenance instruction
+ 1.2. Information before car driving
+ 1.3. Independent maintenance
+ 1.4. Technical characteristics
+ 1.5. Some councils upon car purchase
+ 2. Maintenance
- 3. Engines
   + 3.1.2. Compression check
   - 3.2. 6-cylinder dvukhryadny engines of V6 3,0 l
      3.2.2. Compression check
      3.2.3. Top dead point (VMT) of the N1 piston
      3.2.4. Covers of heads of cylinders
      3.2.5. Inlet collector
      3.2.6. Final collectors
      3.2.7. Gas-distributing belt and asterisks
      3.2.8. Forward epiploon of a cranked shaft
      3.2.9. Epiploons of camshafts
      3.2.10. Camshafts and lifts of valves
      3.2.11. Heads of cylinders
      3.2.12. Oil pallet
      3.2.13. Oil pump
      3.2.14. Flywheel / leader disk
      3.2.15. Back epiploon of a cranked shaft
      3.2.16. Engine fastenings
   + 3.3. Partition of engines
   + 3.4. Engine electric equipment
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. Exhaust system
+ 8. Transmission
+ 9. Running gear
+ 10. Brake system
+ 11. Body
+ 12. Electric equipment

3.2.10. Camshafts and lifts of valves

GENERAL INFORMATION

Sequence of a tightening of bolts of covers of bearings of a shaft of inlet valves (the right head)

Sequence of a tightening of bolts of covers of bearings of a shaft of inlet valves (the left head)

Sequence of a tightening of bolts of covers of bearings of a shaft of final valves (the right head)

Sequence of a tightening of bolts of covers of bearings of a shaft of final valves (the left head)

Removal

PERFORMANCE ORDER

1. Establish the first piston in VMT. Remove covers of heads, a gas-distributing belt and a camshaft asterisk.
	2. Check, that sinkhronizatsionny labels on gear wheels of shaft were combined.
	3. Stop an auxiliary gear wheel of a shaft of final valves, having twisted a bolt in openings of auxiliary and main gear wheels.
4. Weaken bolts of covers of bearings of a shaft of inlet valves in sequence of return sequence of their tightening (see fig. Sequence of a tightening of bolts of covers of bearings of a shaft of inlet valves (the right head), fig. Sequence of a tightening of bolts of covers of bearings of a shaft of inlet valves (the left head). Remove covers of bearings and get a shaft.
5. Weaken bolts of covers of bearings of a shaft of final valves in sequence of return sequence of their tightening (see fig. Sequence of a tightening of bolts of covers of bearings of a shaft of final valves (the right head), fig. Sequence of a tightening of bolts of covers of bearings of a shaft of final valves (the left head)). Remove covers and get a shaft.
6. Similarly remove shaft of other head.
	7. Combine covers of bearings in the correct sequence.
	8. To disassemble a gear wheel of a shaft of final valves, fix a shaft in a vice. By means of a special key weaken pressure upon a boat twisted in gear wheels, and unscrew it.
	9. Remove a lock ring of an auxiliary gear wheel.
	10. Remove an auxiliary gear wheel (3), a spring (2) and washers (1).

Check

Cм. subsection 3.1.10.

Installation

PERFORMANCE ORDER

1. Establish an auxiliary gear wheel and its elements.
2. Fix a shaft in a vice and again twist a bolt in openings of gear wheels of a shaft. Grease with universal greasing lifts of valves (if you removed them) and establish them in the corresponding nests.

3. Grease with special greasing cams and necks of bearings of a shaft of final valves, and establish a shaft in a head. Labels on a gear wheel should be directed towards a shaft of final valves (in drawing on the right – the right head, at the left – left).
	4. Put hermetic on external parts of a being joined surface of a cover of the first bearing (are marked with shading).

5. Establish covers of bearings as numbering. Shooters on covers should be directed towards a gas-distributing belt (in drawing on the right – the right head, at the left – left).
6. Tighten bolts of covers till the demanded moment of an inhaling. Tighten bolts in the specified sequence on the one fourth turn at one time (see fig. Sequence of a tightening of bolts of covers of bearings of a shaft of final valves (the right head), fig. Sequence of a tightening of bolts of covers of bearings of a shaft of final valves (the left head)).
7. Establish a new epiploon of a shaft.
8. Grease with special greasing cams and necks of bearings of a shaft of inlet valves.
	9. Establish a shaft in a head, having combined labels on gear wheels of shaft.

10. Establish covers of bearings as numbering. Shooters on covers should be directed towards a gas-distributing belt (in drawing on the right – the right head, at the left – left).
11. Tighten bolts of covers till the demanded moment of an inhaling. Tighten bolts in the specified sequence on the one fourth turn at one time (see fig. Sequence of a tightening of bolts of covers of bearings of a shaft of inlet valves (the right head), fig. Sequence of a tightening of bolts of covers of bearings of a shaft of inlet valves (the left head)).
12. Unscrew stopping bolt from gear wheels of a shaft of inlet valves.
13. Establish asterisks of shaft and a gas-distributing belt.
14. Establish the remained details.