Toyota Camry

1996-2001 of release

Repair and car operation

Kamri's Toyota
+ 1. Maintenance instruction
+ 1.2. Information before car driving
+ 1.3. Independent maintenance
+ 1.4. Technical characteristics
+ 1.5. Some councils upon car purchase
+ 2. Maintenance
- 3. Engines
   + 3.1.2. Compression check
   - 3.2. 6-cylinder dvukhryadny engines of V6 3,0 l
      3.2.2. Compression check
      3.2.3. Top dead point (VMT) of the N1 piston
      3.2.4. Covers of heads of cylinders
      3.2.5. Inlet collector
      3.2.6. Final collectors
      3.2.7. Gas-distributing belt and asterisks
      3.2.8. Forward epiploon of a cranked shaft
      3.2.9. Epiploons of camshafts
      3.2.10. Camshafts and lifts of valves
      3.2.11. Heads of cylinders
      3.2.12. Oil pallet
      3.2.13. Oil pump
      3.2.14. Flywheel / leader disk
      3.2.15. Back epiploon of a cranked shaft
      3.2.16. Engine fastenings
   + 3.3. Partition of engines
   + 3.4. Engine electric equipment
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. Exhaust system
+ 8. Transmission
+ 9. Running gear
+ 10. Brake system
+ 11. Body
+ 12. Electric equipment

3.2.7. Gas-distributing belt and asterisks

GENERAL INFORMATION

Gas-distributing belt

1. Laying
2. Gas-distributing belt
3. A directing disk of a belt
4. Arm
5. Laying
6. Protective casing of wires
7. Intermediate pulley of N1
8. Cover
9. Plate
10. Natyazhitel of a belt
11. Asterisk of a cranked shaft

12. Washer
13. Intermediate pulley of N2
14. Asterisk of the left camshaft
15. Asterisk of the right camshaft
16. Pulley of a cranked shaft
17. Bottom cover of a belt
18. Right assembly arm of the engine
19. Top cover of a belt

Removal

PERFORMANCE ORDER

1. Disconnect a wire of the minus plug of the accumulator.
2. Remove a broad tank of system of cooling and a tank of stekloomyvatel of a windshield.
3. Remove driving belts of the generator and the pump of system of strengthening of a steering.
4. Weaken bolts of the right forward wheel. Lift and fix a forward part of the car. Remove a wheel. Remove isolation of an arch of a wheel.
5. Establish the cylinder of the first piston in the top dead point.
	6. Unscrew two through bolts (And) and remove the draft regulating shift of the engine (In) and an arm of draft.
7. Remove spark plugs.
	8. Remove the top cover of a gas-distributing belt and laying.
	9. If you are going to reuse a gas-distributing belt, make on it adjusting labels.
	10. Check sinkhronizatsionny labels of asterisks of camshafts. Labels on asterisks of shaft should be combined with labels on a back cover of a belt.
	11. Unscrew two bolts (arrow) and remove a natyazhitel of a belt.
12. Weaken a tension of a belt and remove a belt.
	13. To remove a camshaft asterisk, uncover heads and stop a shaft a wrench (shooter). Braid a bolt of an asterisk and remove an asterisk.
14. Remove the top intermediate pulley.
15. Unscrew a bolt of a pulley of a cranked shaft, previously having stopped a flywheel.
	16. Check sinkhronizatsionny labels and remove a pulley.
17. Remove the bottom cover of a belt and laying.
18. Remove directing disk of a belt.
	19. If you are going to reuse a belt, make an adjusting label on a belt opposite to an opening in an asterisk of a cranked shaft. Remove a belt.

Check

PERFORMANCE ORDER

1. Check a belt (see subsection 3.1.7.).
2. Check, whether the natyazhitel of a belt proceeds, if necessary replace a natyazhitel.
	3. Measure an acting part of a rod of a natyazhitel. If the received size does not correspond to technical requirements, replace a natyazhitel.

Installation

PERFORMANCE ORDER

1. Carefully clean a forward part of the engine.
	2. Establish an asterisk of a cranked shaft (if you removed it) and combine a label of a sinkhronizatsionny asterisk with a label on the block of cylinders (And) and establish an asterisk clamp (In).
3. Grease the bottom intermediate rod with hermetic, establish a pulley and tighten a bolt till the demanded moment of an inhaling.
4. Put on a belt, using adjusting labels.
5. Put on directing disk of a belt and the bottom cover of a belt.
6. Establish a pulley of a cranked shaft and tighten a pulley bolt.
7. Establish the top intermediate pulley and tighten an assembly bolt.
8. Establish asterisks of camshafts. The flange of a forward asterisk should be directed outside, and a flange of a back asterisk inside. Check, that sinkhronizatsionny labels on asterisks and on a back cover of a belt were combined. Tighten bolts of asterisks till the demanded moment of an inhaling.
9. Put on a belt asterisks of camshafts, using adjusting labels.
	10. By means of a vice, press a rod of a natyazhitel. Insert a shtoporny pin in diameter of 1,27 mm into openings of a casing and a rod of a natyazhitel.
11. Establish a natyazhitel and tighten his bolts. Get the lock probe of a rod.
12. Turn a cranked shaft clockwise on two complete revolutions. Check sinkhronizatsionny labels.
13. Establish the remained details.