Toyota Camry

1996-2001 of release

Repair and car operation

Kamri's Toyota
+ 1. Maintenance instruction
+ 1.2. Information before car driving
+ 1.3. Independent maintenance
+ 1.4. Technical characteristics
+ 1.5. Some councils upon car purchase
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
- 7. Exhaust system
   - 7.2. Systems of decrease in toxicity of exhaust gases
      7.2.2. Technical characteristics
      7.2.3. OBD II system
      7.2.4. OBD computer of II system (Powertrain Control Module)
      7.2.5. Sensor of turn of a butterfly valve
      7.2.6. The sensor of absolute pressure in a soaking-up collector
      7.2.7. Sensor of a mass consumption of air
      7.2.8. The sensor of temperature of soaked-up air (IAT sensor)
      7.2.9. The sensor of temperature of cooling liquid (ECT sensor)
      7.2.10. Sensor of rotation of the crankshaft
      7.2.11. Sensor of rotation of a cam-shaft
      7.2.12. Contact sensor of pressure of the hydraulic booster
      7.2.13. The sensor of the content of oxygen in the fulfilled gases
      7.2.14. Detonation sensor
      7.2.15. Sensor of speed of the car
      7.2.16. Perepuskna air valve of idling (IAC valve)
      7.2.17. System of a choice of the channel absorptions (ACIS system)
      7.2.18. System of ventilation of a case
      7.2.19. Retsirkulyatsiya system
      7.2.20. Catching system паров gasoline
      7.2.21. Converter
      7.2.22. Rub in one – or how to save the catalyst
+ 8. Transmission
+ 9. Running gear
+ 10. Brake system
+ 11. Body
+ 12. Electric equipment

7.2.10. Sensor of rotation of the crankshaft

GENERAL INFORMATION

On 4-cylinder engines the sensor is mounted under a cover of a gear belt, on V6 engines – over a crankshaft pulley.

Place of installation of the sensor of rotation of the crankshaft on 4-cylinder engines

1. Wire
2. Socket
3. Generator
4. Directing a crankshaft pulley
5. Sensor of rotation of the crankshaft
6, 7, 9, 14. Collar

8. Sensor socket
10. Pulley
11. Cover of N1 of a belt
12. Cover of N2 of a belt
13, 15. Laying

Place of installation of the sensor of rotation of the crankshaft on 6-cylinder engines

1. Socket

2. Sensor

Check

4-CYLINDER ENGINES

PERFORMANCE ORDER

	1. Disconnect the socket of conducting of the sensor about the generator and check resistance of the sensor (the arrow specified a sensor arrangement).
2. Together with the sensor it is necessary to check and the computer module for what it is necessary to remove and hand over the module in car-care center.

6-CYLINDER ENGINES

PERFORMANCE ORDER

	1. Because of the complicated access to the socket the sensor is recommended to be removed (an arrow specified a sensor arrangement). Check resistance on the removed sensor.
2. Having warmed up the engine, or having removed the sensor and having placed in boiled water, check resistance of the sensor at 80 ° With which should be 250–300 Ohm.

Replacement

PERFORMANCE ORDER

1. Disconnect the battery from weight.

2. On 4-cylinder engines uncover a belt (see fig. A place of installation of the sensor of rotation of the crankshaft on 4-cylinder engines).

3. On 6-cylinder engines for access to the sensor remove the protective panel of a wheel niche (see fig. A place of installation of the sensor of rotation of the crankshaft on 6-cylinder engines). Disconnect the socket, unscrew a bolt and remove the sensor.