Toyota Camry

1996-2001 of release

Repair and car operation

Kamri's Toyota
+ 1. Maintenance instruction
+ 1.2. Information before car driving
+ 1.3. Independent maintenance
+ 1.4. Technical characteristics
+ 1.5. Some councils upon car purchase
+ 2. Maintenance
- 3. Engines
   + 3.1.2. Compression check
   + 3.2. 6-cylinder dvukhryadny engines of V6 3,0 l
   - 3.3. Partition of engines
      3.3.1.2. 6-cylinder dvukhryadny engines
      3.3.2. Major maintenance of the engine – general comments
      3.3.3. Engine diagnostics by means of the vacuum gage
      3.3.4. Major maintenance of the engine – alternatives
      3.3.5. Auxiliary elements of the engine
      3.3.6. Removal and engine installation
      3.3.7. Engine partition
      3.3.8. Head of cylinders and valves
      3.3.9. Balancing device (the 4-cylinder engine)
      3.3.10. Pistons and rods
      3.3.11. Cranked shaft
      3.3.12. Block of cylinders
      3.3.13. Honingovaniye of cylinders
      3.3.14. Radical bearings and bearings of rods
      3.3.15. Measurement of size of a free wheeling of the balancing device
      3.3.16. Piston rings
      3.3.17. Radical bearings of a cranked shaft
      3.3.18. Back epiploon of a cranked shaft
      3.3.19. Shatunnye bearings
      3.3.20. Installation of the balancing device of the engine
      3.3.21. It is rather live, than it is dead …
      3.3.22. Analysis of a dymnost of an exhaust
      3.3.23. A gear belt for a drive of the mechanism of a gazoraspredeleniye
      3.3.24. Emergence in deposit oil
      3.3.25. Engine overheat
   + 3.4. Engine electric equipment
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. Exhaust system
+ 8. Transmission
+ 9. Running gear
+ 10. Brake system
+ 11. Body
+ 12. Electric equipment

3.3.12. Block of cylinders

Cleaning

PERFORMANCE ORDER

	1. Turn caps in openings, having struck with a stupid core of a pobokovy part of each cap.
	2. Take plastic caps flat-nose pliers.
	3. In the 6-cylinder engine instead of plastic caps metal plates are established.
4. By means of a plastic scraper clean off all traces of hermetic from a being joined surface of the block of cylinders.
5. Unscrew or drill caps of oil channels from the block of cylinders. Use new caps during assembly.
6. If too dirty, it it is necessary to clean the block in a specialized workshop.
7. Clean and wash out oil openings and channels warm water. Dry openings and channels, having blown them the compressed air. Grease the block with anticorrosive oil.
	8. Clean carvings of openings in the block by means of taps of the necessary size. Clean bolts of a head of cylinders and bolts of radical bearings.
9. Establish covers of radical bearings and twist bolts.
	10. By means of the special tool hammer new, greased with hermetic, caps into block openings.
11. Put hermetic on caps of oil channels and twist them in the block.

Check

PERFORMANCE ORDER

1. Examine the block on existence of cracks and corrosion or rust traces. Examine carvings of openings of the block. At detection of defects, it is necessary to repair or replace the block whenever possible.
2. Examine cylinders and check them on a konusnost and ovality.
	3. Measure diameter of each cylinder perpendicular to the central line (And) and parallel to the central line (In) (1 – the central line of the engine).
	4. Measure diameter of the cylinder by means of a telescopic measuring instrument.
	5. Measure length of a telescopic measuring instrument by means of a micrometer.
6. Measure diameter of each cylinder in the top average and bottom its parts, perpendicular to an axis of a cranked shaft.
7. The Konusnost of the cylinder is calculated as a difference between top and bottom in diameters. Ovality – as a difference between parallel and perpendicular measurements.
8. If the received results do not coincide with technical requirements, cylinders are necessary for processing in a specialized workshop.
	9. By means of a ruler and щупов check, whether the surface of the block which is joining to a head is deformed.
10. Check wear of pistons and cylinders with the help щупов. When finding wear or damages at block survey, address to experts.