Toyota Camry

1996-2001 of release

Repair and car operation

Kamri's Toyota
+ 1. Maintenance instruction
+ 1.2. Information before car driving
+ 1.3. Independent maintenance
+ 1.4. Technical characteristics
+ 1.5. Some councils upon car purchase
+ 2. Maintenance
- 3. Engines
   + 3.1.2. Compression check
   + 3.2. 6-cylinder dvukhryadny engines of V6 3,0 l
   - 3.3. Partition of engines
      3.3.1.2. 6-cylinder dvukhryadny engines
      3.3.2. Major maintenance of the engine – general comments
      3.3.3. Engine diagnostics by means of the vacuum gage
      3.3.4. Major maintenance of the engine – alternatives
      3.3.5. Auxiliary elements of the engine
      3.3.6. Removal and engine installation
      3.3.7. Engine partition
      3.3.8. Head of cylinders and valves
      3.3.9. Balancing device (the 4-cylinder engine)
      3.3.10. Pistons and rods
      3.3.11. Cranked shaft
      3.3.12. Block of cylinders
      3.3.13. Honingovaniye of cylinders
      3.3.14. Radical bearings and bearings of rods
      3.3.15. Measurement of size of a free wheeling of the balancing device
      3.3.16. Piston rings
      3.3.17. Radical bearings of a cranked shaft
      3.3.18. Back epiploon of a cranked shaft
      3.3.19. Shatunnye bearings
      3.3.20. Installation of the balancing device of the engine
      3.3.21. It is rather live, than it is dead …
      3.3.22. Analysis of a dymnost of an exhaust
      3.3.23. A gear belt for a drive of the mechanism of a gazoraspredeleniye
      3.3.24. Emergence in deposit oil
      3.3.25. Engine overheat
   + 3.4. Engine electric equipment
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. Exhaust system
+ 8. Transmission
+ 9. Running gear
+ 10. Brake system
+ 11. Body
+ 12. Electric equipment

3.3.17. Radical bearings of a cranked shaft

GENERAL INFORMATION

Sequence of a tightening of bolts of covers of radical bearings (4-cylinder engines)

Sequence of a tightening of bolts of the block of covers of radical bearings (6-cylinder engines)

Sequence of a tightening of lateral bolts of covers of radical bearings (6-cylinder engines)

Check of a lubricant gap of radical bearings

PERFORMANCE ORDER

1. Establish new loose leaves of radical bearings.
2. Clear a cranked shaft, bearings and lubricant openings, then accurately establish a cranked shaft on bearings.
	3. Put a plastic piece on each of radical bearings along a shaft axis.
4. Establish covers of radical bearings, trying not to shift plastic. Tighten fixing bolts of covers till the demanded moment of an inhaling in the specified sequence (see fig. Sequence of a tightening of bolts of covers of radical bearings (4-cylinder engines), fig. Sequence of a tightening of bolts of the block of covers of radical bearings (6-cylinder engines), fig. Sequence of a tightening of lateral bolts of covers of radical bearings (6-cylinder engines). Do not turn a cranked shaft.
	5. In 6-cylinder engines after you tightened bolts till the demanded moment of an inhaling of the first step, hold on on a turn quarter.
6. Unscrew bolts, and accurately remove covers.
	7. Compare width of the crushed film to a special scale for determination of size of a lubricant gap.
8. If the size of a gap does not correspond to technical requirements, establish loose leaves of other size. If necessary bearings can be ground.
9. Carefully remove film traces from a shaft and bearings.

Final installation of a cranked shaft

PERFORMANCE ORDER

1. Accurately remove a cranked shaft.
2. Clear a surface of loose leaves and grease them with greasing or engine oil. Check, that bearings of a cranked shaft were pure and establish a cranked shaft into place. Grease and establish the bottom loose leaves. Establish persistent half rings.
	3. In 4-cylinder engines establish persistent half rings in a cover of the third bearing, and in 6-cylinder – in a cover of the second bearing.
4. Establish covers of radical bearings. Shooters of covers should be directed towards a forward part of the engine. Insert and tighten bolts of covers of all radical bearings till the demanded moment of an inhaling in the specified sequence (see fig. Sequence of a tightening of bolts of covers of radical bearings (4-cylinder engines), fig. Sequence of a tightening of bolts of the block of covers of radical bearings (6-cylinder engines), fig. Sequence of a tightening of lateral bolts of covers of radical bearings (6-cylinder engines).
	5. Do not forget to establish new sealing washers on lateral six-sided bolts.
6. Turn a cranked shaft a hand several times and check ease of a course.
7. Check axial люфт a cranked shaft and establish a back epiploon.