Toyota Camry

1996-2001 of release

Repair and car operation

Kamri's Toyota
+ 1. Maintenance instruction
+ 1.2. Information before car driving
+ 1.3. Independent maintenance
+ 1.4. Technical characteristics
+ 1.5. Some councils upon car purchase
+ 2. Maintenance
- 3. Engines
   + 3.1.2. Compression check
   + 3.2. 6-cylinder dvukhryadny engines of V6 3,0 l
   - 3.3. Partition of engines
      3.3.1.2. 6-cylinder dvukhryadny engines
      3.3.2. Major maintenance of the engine – general comments
      3.3.3. Engine diagnostics by means of the vacuum gage
      3.3.4. Major maintenance of the engine – alternatives
      3.3.5. Auxiliary elements of the engine
      3.3.6. Removal and engine installation
      3.3.7. Engine partition
      3.3.8. Head of cylinders and valves
      3.3.9. Balancing device (the 4-cylinder engine)
      3.3.10. Pistons and rods
      3.3.11. Cranked shaft
      3.3.12. Block of cylinders
      3.3.13. Honingovaniye of cylinders
      3.3.14. Radical bearings and bearings of rods
      3.3.15. Measurement of size of a free wheeling of the balancing device
      3.3.16. Piston rings
      3.3.17. Radical bearings of a cranked shaft
      3.3.18. Back epiploon of a cranked shaft
      3.3.19. Shatunnye bearings
      3.3.20. Installation of the balancing device of the engine
      3.3.21. It is rather live, than it is dead …
      3.3.22. Analysis of a dymnost of an exhaust
      3.3.23. A gear belt for a drive of the mechanism of a gazoraspredeleniye
      3.3.24. Emergence in deposit oil
      3.3.25. Engine overheat
   + 3.4. Engine electric equipment
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. Exhaust system
+ 8. Transmission
+ 9. Running gear
+ 10. Brake system
+ 11. Body
+ 12. Electric equipment

3.3.6. Removal and engine installation

Removal

PERFORMANCE ORDER

1. Pit pressure in fuel system.
2. Disconnect a wire of the minus plug of the accumulator.
3. Remove the accumulator and an accumulator arm.
4. Remove an engine cowl.
5. Remove the air filter.
6. Lift and fix the car. Merge cooling liquid and engine oil. Remove driving belts.
	7. Mark both ends disconnect vacuum hoses, hoses of cooling liquid and final gases. Disconnect wires and fuel tubes. To mark wires use an insulating tape.
8. Remove a broad tank of system of cooling and a tank of stekloomyvatel.
9. Remove radiator fans, a casing of fans and a radiator.
10. Disconnect heater hoses.
11. Disconnect the fuel tubes connecting the engine to a body.
12. Disconnect from the engine a butterfly valve rope, a rope of the throttle valve of a transmission and a rope of the sensor of a speedometer.
13. Disconnect holders of a plait of wires of the engine.
14. Unscrew assembly bolts of the pump of system of strengthening of a wheel. Whenever possible shift the pump aside without disconnecting from it hoses. If necessary remove the pump.
	15. Remove the compressor of the air conditioner and shift it aside. Do not disconnect hoses from the compressor.
16. Disconnect an exhaust pipe (ы) from a collector (ов).
	17. In four-cylinder engines remove the oil filter, disconnect hoses from an oil radiator and remove an oil radiator (shooter).
18. Fix a chain on hooks intended for a raising of the engine and connect a chain to the lift.
	19. Remove a leading axis (And) from passenger sitting, unscrew a through bolt of a support of the engine (In) and remove a back arm of the engine (C).
	20. Unscrew a bolt, fixing a forward support of the engine to a body (And) if you remove the engine together with a transmission, remove the engine shock-absorber (In).
21. In models with an automatic transmission remove the dustproof screen of the hydrotransformer, remove clamps of the hydrotransformer and slightly press the hydrotransformer into a transmission casing.
22. If you remove only the engine, unscrew bolts and disconnect a transmission.
23. Check that nothing disturbed engine removal.
24. Establish a jack under a transmission. Unscrew bolts from engine support.
	25. Slowly lift the engine on the lift (in drawing the 4-cylinder engine together with a transmission is shown).
26. Lower the engine on specially equipped rack or on a workshop floor.

Installation

PERFORMANCE ORDER

1. In engines with a mechanical transmission, examine elements of coupling and grease press the bearing.

2. In engines with an automatic transmission, examine laying and the plug of the hydrotransformer and grease its forward part.

3. Establish the engine upside-down removals.