Toyota Camry

1996-2001 of release

Repair and car operation

Kamri's Toyota
+ 1. Maintenance instruction
+ 1.2. Information before car driving
+ 1.3. Independent maintenance
+ 1.4. Technical characteristics
+ 1.5. Some councils upon car purchase
+ 2. Maintenance
- 3. Engines
   + 3.1.2. Compression check
   + 3.2. 6-cylinder dvukhryadny engines of V6 3,0 l
   - 3.3. Partition of engines
      3.3.1.2. 6-cylinder dvukhryadny engines
      3.3.2. Major maintenance of the engine – general comments
      3.3.3. Engine diagnostics by means of the vacuum gage
      3.3.4. Major maintenance of the engine – alternatives
      3.3.5. Auxiliary elements of the engine
      3.3.6. Removal and engine installation
      3.3.7. Engine partition
      3.3.8. Head of cylinders and valves
      3.3.9. Balancing device (the 4-cylinder engine)
      3.3.10. Pistons and rods
      3.3.11. Cranked shaft
      3.3.12. Block of cylinders
      3.3.13. Honingovaniye of cylinders
      3.3.14. Radical bearings and bearings of rods
      3.3.15. Measurement of size of a free wheeling of the balancing device
      3.3.16. Piston rings
      3.3.17. Radical bearings of a cranked shaft
      3.3.18. Back epiploon of a cranked shaft
      3.3.19. Shatunnye bearings
      3.3.20. Installation of the balancing device of the engine
      3.3.21. It is rather live, than it is dead …
      3.3.22. Analysis of a dymnost of an exhaust
      3.3.23. A gear belt for a drive of the mechanism of a gazoraspredeleniye
      3.3.24. Emergence in deposit oil
      3.3.25. Engine overheat
   + 3.4. Engine electric equipment
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. Exhaust system
+ 8. Transmission
+ 9. Running gear
+ 10. Brake system
+ 11. Body
+ 12. Electric equipment

3.3.7. Engine partition

GENERAL INFORMATION

The 4-cylinder engine – elements of the block of cylinders

1. Piston ring (kompressionny)
2. Piston ring (maslosjemny)
3. Piston finger
4. Rod plug
5. Block of cylinders
6. Back plate
7. Laying
8. Back epiploon of a cranked shaft
9. Casing of a back epiploon
10. Flywheel or leading disk
11. Leading disk
12. Back intermediate ring
13. Forward intermediate ring
14. Balancing device
engine
15. Laying
16. Maslozaborny branch pipe
17. Laying

18. Dividing partition of the oil pallet
19. Cover of the radical bearing
20. Loose leaf of the radical bearing
21. Persistent half ring
22. Cranked shaft
23. Laying
24. Oil pump
25. Forward epiploon of a cranked shaft
26. Right arm of the engine
27. Arm of the pump of the hydraulic booster
28. Rod cover
29. Loose leaf of the shatunny bearing
30. Rod
31. Lock ring
32. Piston
33. Spring of a maslosjemny ring
34. Piston ring (kompressionny)

The 6-cylinder dvukhryadny engine – elements of the block of cylinders

1. Piston ring (kompressionny)
2. Piston ring (kompressionny)
3. Piston ring (maslosjemny)
4. Piston
5. Rod plug
6. Rod
7. Loose leaf of the shatunny bearing
8. Rod cover
9. Back plate
10. Flywheel
11. Back epiploon of a cranked shaft
12. Casing of a back epiploon
13. Arm of the oil filter
14. Back intermediate ring
15. Leading disk
16. Forward intermediate ring
17. Loose leaf of the radical bearing
18. Cover of the radical bearing

19. Sealing washer
20. Sealing half ring
21. Cranked shaft
22. Maslozaborny branch pipe
23. Laying
24. Sensor of pressure of oil
25. Oil pump
26. Epiploon
27. Sealing ring
28. Sensor of detonation combustion
29. Clamp
30. Drain hose
31. Drain crane
32. Lock ring
33. Porshnevy finger
34. Spring of a maslosjemny ring
35. A tube of cooling liquid
36. Arm of an intermediate pulley

Carry out an engine partition in the pure place specially equipped for this purpose.

Fix the engine at the special stand, or on a floor.

Prepare all necessary tools and observe precautionary measures during carrying out this difficult procedure.